Shift Lock Solenoid Removal and Installation CR-V

Service Manual

Shift Lock Solenoid Removal and Installation

743145

NOTE: Do not wipe off the special grease applied to the area of the shift lever marked with an asterisk (*) when you disassemble it- 1.Center Console Panel Assembly (Except '12M M/T)

1- Detach the clips (A)-

2- Remove the center console panel (A)- 3- For some models: Disconnect the connector(s) (B)- 2.Cup Holder Panel Assembly

1- Remove the cup holder panel assembly (A)- 3.Center Console Assembly

1- Remove the bolts (A)- 2- Disconnect the connector (B)-

3- Remove the console box mat (A)- 4- Remove the bolts (B)-

5- Disconnect the connector (A)-

6- Remove the center console (A), in the numbered sequence shown- 4.Shift Lever Knob and Shift Lever Knob Ring

1- Pull down the shift lever ring (A)- 2- Wrap the end of a flat-tip screwdriver (B) with tape, remove the shift lever knob ring (C)-

3- Remove the shift lever knob (A) and the shift lever ring (B)- 5.A/T Gear Position Indicator Panel Assembly (Type A Shift Lever)

1- Disconnect the connector (A)- 2- Remove the A/T gear position indicator panel assembly (B) by expanding the four lock tabs (C)- 6.Shift Lock Unit Assembly (Type A Shift Lever)

1- Disconnect the connectors (A)- 2- Release the lock tab (B) and turn the pivot pin (C) counterclockwise using a hex wrench (D) as shown, and pull it- 3- Remove the shift lock unit (E) while releasing the four lock tabs (F)- 7.Shift Lock Solenoid

Type A shift lever

Type A shift lever

1- Type A shift lever: Pull the shift lock solenoid (A) out by expanding the lock tabs (B)- Type A shift lever

2- Type A shift lever: Remove the shift lock solenoid (A)- NOTE: The shift lock solenoid consists of the solenoid (B), the solenoid plunger (C), and the plunger spring (D)- Type B shift lever

Type B shift lever

1- Type B shift lever: Disconnect the connector (A)- 2- Type B shift lever: Remove the connector clamp (B)- Type B shift lever

3- Type B shift lever: Pull the shift lock solenoid (A) out by expanding the lock tab (B)- Type B shift lever

4- Type B shift lever: Remove the shift lock solenoid (A)- NOTE: The shift lock solenoid consists of the solenoid (B), the solenoid plunger (C), and the plunger spring (D)-

NOTE: Do not wipe off the special grease applied to the area of the shift lever marked with an asterisk (*) when you assemble it- 1.Shift Lock Solenoid

Type A shift lever

Type A shift lever

1- Type A shift lever: Install the shift lock solenoid (A) by aligning the joint of the shift lock solenoid plunger (B) with the tip of the shift lock stop (C)- NOTE: The shift lock solenoid consists of the solenoid (D), the solenoid plunger (E), and the plunger spring (F)- Type B shift lever

Type B shift lever

1- Type B shift lever: Install the shift lock solenoid (A) by aligning the joint of the shift lock solenoid plunger (B) with the tip of the shift lock stop (C)- NOTE: The shift lock solenoid consists of the solenoid (D), the solenoid plunger (E), and the plunger spring (F)- Type B shift lever

2- Type B shift lever: Route the shift lock solenoid harness (A) along the harness guides (B)- 3- Type B shift lever: Install the connector clamp (C)- 4- Type B shift lever: Connect the connector (D)- 2.Shift Lock Unit Assembly (Type A Shift Lever)

1- Install the shift lock unit (A) by aligning the four lock tabs (B)- 2- Push the pivot pin (C), and turn it clockwise using a hex wrench (D) as shown- 3- Connect the connectors (E)- 3.A/T Gear Position Indicator Panel Assembly (Type A Shift Lever)

1- Install the A/T gear position indicator panel assembly (A) by aligning the four lock tabs (B)- 2- Connect the connector (C)- 4.Shift Lever Knob and Shift Lever Knob Ring

1- Install the shift lever knob (A) and the shift lever ring (B)-

2- Pull down the shift lever ring (A) if necessary, and install the shift lever knob ring (B)- 3- Pull up the shift lever ring to secure the knob ring- 5.Center Console Assembly

1- Install the center console (A), in the numbered sequence shown-

2- Connect the connector (A)-

3- Install the bolts (A)- 4- Install the console box mat (B)-

5- Connect the connector (A)- 6- Install the bolts (B)- 6.Cup Holder Panel Assembly

1- Install the cup holder panel assembly (A)- 7.Center Console Panel Assembly (Except '12M M/T)

1- For some models: Connect the connector(s) (A)- 2- Install the center console panel (B)-

3- Install the clips (A).

See also:
M/T Differential Carrier and Final Driven Gear Removal and Installation CR-V...7007
Service Manual M/T Differential Carrier and Final Driven Gear Removal and Installation 2131F3 Removal 1.M/T Change Lever Assembly 1- Remove the change lever assembly (A)- 2- Remove the...
Steering Column/EPS Control Unit Removal and Installation CR-V
Steering Column/EPS Control Unit Removal and Installation NOTE: SRS components are located in this area. Review the SRS component locations, and the precautions and procedures before doing...
Synchro Sleeve and Hub Disassembly, Reassembly, and Inspection CR-V...7074
Trans/Driveline Synchro Sleeve and Hub Disassembly, Reassembly, and Inspection Special Tools Required ImageDescription/Tool NumberDriver Handle, 40 mm I.D. 07746-0030100Bearing Driver...